Go Easy with These Tips on How to Patch Drywall Holes

24 views
Go Easy with These Tips on How to Patch Drywall Holes

Don’t worry if a doorknob or misguided chair knocks a hole in your drywall. Drywall is vulnerable to dents and it is okay if you got one in drywall. It is quite easier than you may think to fix drywall. With little patience, a bit of joint compound, and few dabs you can fix your drywall. I have come up with some of the easy guides that tell how to patch drywall.

With these easy steps, even a novice can complete wall repair. However, we must know the tool that should be handy while walking you through more important steps on how to dry patch drywall. Here is a sneak peek at the list of tools and the material you need.

Tools and Material Needed

Right before getting started on drywall areas, it is important to know all the prerequisites of the task. Achieve professional job-like expertise by using the right tool and material to patch the drywall.

  • Sander.
  • Dust mask.
  • Saw for drywall.
  • Paintbrush.
  • Screw gun.
  • Taping knife.
  • Utility knife.
  • Drywall.
  • Screws.
  • Tape for drywall.
  • Joint compound.

Key Point

Decide whether you have to paint the whole wall or just patched areas depending upon the drywall area that needs a redo. According to this area, choose the quantity of paint and drywall compound joint. Also, if you are patching a large number of holes, you must prime the patched wall before repainting.

How to Patch Drywall

Drywall is prone to dents especially when preparing for a move. But the good thing is that you can easily patch drywall using some techniques. However, it is important to wear safety glasses and a mask before doing any kind of drywall repair. Here is a quick read on drywall.

How to Patch a Hole in Drywall in an Easy Way

Many of the drywalls are prone to tiny holes for example small nail holes, screws holes, and popped nail heads. This is the most common type of drywall damage and hence knowing how to patch a hole in drywall should be every renter’s prime concern.

Here are some easy steps that will patch a tiny hole in drywall:

  • Firstly, fill holes with lightweight spackle using your fingers or a putty knife.
  • Make sure that you have filled the hole with a spackle. Now level this spackle with the rest of the undamaged wall.
  • Leave the spackle for 15 to 30 minutes or the time recommended by the manufacturer. The spackle needs to be dried completely before stepping into the next step.
  • Use fine-grit sandpaper to sand the patched area and make it smooth.
  • Brush away any remains and apply paint to the area.
  • In contrast, sometimes the size of a hole is larger than a typical nail hole and you may need a drywall patch kit to repair it. The kit will have a 4-inch by 4-inch adhesive drywall patch and some other tools that you may require to fix the hole. Here is a quick read for a hole that is less than 4 inches across the drywall. Follow the following steps to fix it:
  •  Cover the hole with a self-adhesive mesh patch and spread spackle or lightweight joint compound. You need to use a putty knife to spread the same over the patched area.
  • Spread the compound in a crisscross pattern smoothly, feathering the edges so that it blends completely into the wall.
  • As per the recommended time of the manufacturer of the joint compound, leave the drywall patch to dry. This may take a maximum of 24 hours.
  • If needed, put a second coat of compound joints and fill the area.
  • You must now smooth the area using sandpaper.
  • Touch up the patched area with the wall paint.

how to patch a hole in drywall

Source: thdstatic.com

how to patch a hole in drywall

Image Source: thdstatic.com

how to patch a hole in drywall

Source: thdstatic.com

how to patch a hole in drywall

Image Source: thdstatic.com

how to patch a hole in drywall

Source: thdstatic.com

how to patch a hole in drywall

Image Source: thdstatic.com

how to patch a hole in drywall

Source: thdstatic.com

how to patch a hole in drywall

Image Source: thdstatic.com

Key Point

If it has been a while you last painted your drywall, you need to paint the entire drywall rather than this small patched area. In addition to this, painting complete drywall can complete a nearly invisible wall repair and ensures a color match.

How to Patch a Large Hole in Drywall in an Easy Way

Sometimes the size of the hole in drywall is big. For more than 4 inches of the hole, you need to patch drywall with a new piece of drywall. After researching for hours, I have come up with some easy ways that tell you how to patch a large hole in drywall. Follow the following steps to know about it:

1. Cutting the Damaged Area Out Would Be First Step in My How to Patch Drywall Guide

how to patch a large hole in drywall

Source: pinimg.com

how to patch a large hole in drywall

Source: pinimg.com

  • Use a carpenter square and pencil, draw a line at least an inch or more above and below the damaged area.
  • Next, you need a stud finder and find the nearest stud on either side of the hole. Use a pencil to encircle these holes.
  • Use a drywall saw and cut along the lines that you drew in the first bullet point until you reach wall studs.
  • On reaching a stud mark measure and mark 3/4 of an inch farther in, that will be the center of a stud. Use a utility knife to score these lines.
  • Make sure that the edge of the patch is over the stud so that both the patched drywall and the existing drywall have support.
  • Continue cutting with each cut slightly deeper than the previous cut. Know that you are cutting along the lines drawn earlier.
  • Remove the damaged piece of drywall.

Key Point

You must always cut away from the body.

2. Cutting Support for the Drywall and Then Installing It into the Same Would Be the Second Step in My How to Patch Drywall Guide

how to patch a large hole in drywall

Source: familyhandyman.com

  • A 1 x 3-inch piece of scrap lumber or 3/4-inch piece of plywood may work for you. But make sure that the piece is approximately 2 to 4 inches longer than the height of the patch that needs to be fixed in drywall.
  • Screw the support vertically behind the opening drywall. You can use drywall screws to fix it. Keeping it vertically with the help of drywall screws will prevent the patch from cracking.
  • Sink the heads of the screw slightly below the surface of the drywall. This will help in smooth finishing.

3. Cutting the Drywall Patch Would Be Third First Step in My How to Patch Drywall Guide

how to patch a large hole in drywall

Source: pinimg.com

  • Create a patch from a 2 x 2-inch piece of drywall by tracing it to the piece of drywall that you have removed in step 1. Ensure that the patch is of the same size.
  • You can use a utility knife and carpenters square to cut the patch of the accurate size.
  • Test fit the patch in the drywall opening. It is important to ensure that the patch is of the same size as that of the drywall opening and it is a good fit. Make sure that it is secure but not too snug to fit into the opening. You must need not force the piece into the opening.

4. Installing a Drywall Patch Would Be Fourth Step in My How to Patch Drywall Guide

how to patch a large hole in drywall

Source: pinimg.com

  • You must position the drywall screws right at an inch from the edges to install drywall a patch. Keeping an inch difference is important to avoid any kind of splitting and crumbling of drywall.
  • You next need a drill. You have to use a drill to secure the patch and wall studs. Sink in the screws slightly below the surface of drywall to ensure smooth polishing later.

5. Taping and Sealing a Drywall Patch Flawlessly Would Be Last Step in My How to Patch Drywall Guide

how to patch a large hole in drywall

Source: mr-maid.com

  • You must run strips of self-adhesive fiberglass drywall tape around the edges of the patch. Center the tape on the seams for proper sealing.
  • You must now spread a drywall joint compound across the patch and tape and create a smooth flat surface all around. Use a 6-inch drywall knife to spread the joint compound across the patch.
  • Let the drywall joint compound dry overnight or as per the time recommended by the manufacturer of the drywall compound joint.
  • You must snow smooth the patch by sanding it using sandpaper.
  • Repeat the second coat of drywall joint compound to fill all the gaps left behind. Let it dry for the next step listed in a bullet.
  • For a very smooth drywall patching, you can apply a third coat of drywall compound joint. You need to spread the third coat with a 12-inch drywall taping knife. Let it dry overnight.
  • Now sand the patch and brush off the extra drywall compound joint. Wipe the patched area with a cloth before applying the paint.
  • Paint the wall to have a mesmerizing original look of new drywall.

Key Point

Since you have to cut drywall, make sure that you know where electrical wires and other utilities pass through the drywall. You can also use a stud finder to find wall studs and where most of the wall wires are attached.

Conclusion

Whether you are a renter or a homemaker, patching drywall is an essential skill that you must acquire. Knowing damage, you can make all the inexpensive repairs wholly yourself. The above-mentioned guide on how to patch drywall will teach you well to fix drywalls without hiring any professional expertise.

Keep coming to Innovativedecorideas for more helpful articles on house improvement and decoration.

For more information, visit innovativedecorideas.

Innovative Decor Ideas

Leave a Reply

Your email address will not be published. Required fields are marked *